Tag: EVERSOLO

  • Eversolo C10 Brings Precision Clocking to Its Flagship Digital Audio System

    Eversolo C10 Brings Precision Clocking to Its Flagship Digital Audio System

    에버솔로 Eversolo C10

    Eversolo C10

    Eversolo has confirmed the full specifications and pricing of its C10 High-Precision Master Clock, a dedicated timing reference designed for high-performance digital audio systems. First shown at HIGH END Vienna 2026 in June, the C10 combines a custom 10MHz SC-cut OCXO with four independently buffered clock outputs, enabling compatible digital audio components to operate from a common timing reference.

    The C10 completes Eversolo’s flagship digital source configuration alongside the T10 streaming transport and DAC-Z10 digital-to-analog converter.


    SC-Cut OCXO for High-Stability Clock Generation

    At the heart of the C10 is a custom 10MHz oven-controlled crystal oscillator (OCXO). By maintaining the crystal at a carefully regulated operating temperature, the oscillator minimizes frequency drift caused by changes in ambient conditions.

    Eversolo employs an SC-cut (Stress Compensated Cut) quartz crystal, a design intended to reduce sensitivity to temperature variation and mechanical stress while improving long-term frequency stability and phase-noise performance.

    The manufacturer specifies phase noise of no more than −115dBc/Hz at a 1Hz offset, −129dBc/Hz at 10Hz, −139dBc/Hz at 100Hz, and −145dBc/Hz at 1kHz. The quoted noise floor is −170dBc/Hz or lower.

    Factory-calibrated frequency offset is specified at less than ±0.01ppm at 10MHz and 25°C, while short-term frequency stability is rated at better than 9×10⁻¹³ over a one-second measurement interval.


    Four Independent Outputs and Nine Clock Frequencies

    The C10 provides four BNC clock outputs, each equipped with a dedicated buffer circuit to minimize interactions between connected components.

    Nine output frequencies are supported: 10MHz, 25MHz, 100MHz, 11.2896MHz, 22.5792MHz, 45.1584MHz, 12.288MHz, 24.576MHz, and 49.152MHz.

    This range includes frequencies associated with both the 44.1kHz and 48kHz sampling-rate families, extending compatibility across different digital audio architectures.

    The outputs deliver a 1.8Vrms square-wave signal with 50Ω output impedance. Compatibility depends on the connected component’s supported clock frequencies, signal requirements, and input configuration.


    GNSS 1PPS Reference for Long-Term Accuracy

    An SMB connector on the rear panel accepts an external GNSS-derived 1PPS (Pulse Per Second) reference signal.

    By using this satellite-derived timing reference, the C10 can periodically correct its internal time base to maintain long-term frequency accuracy.

    The arrangement combines the oscillator’s short-term stability with the long-term accuracy available from an external timing reference, providing an additional means of maintaining consistent clock performance during extended operation.


    Real-Time Clock Monitoring on an 8.8-Inch Touchscreen

    One of the C10’s most distinctive features is its 8.8-inch IPS touchscreen.

    Rather than limiting feedback to a simple status indicator, the display presents the oscillator’s operating temperature, stabilization process, clock status, and 1PPS calibration information.

    Users can follow the transition from Warm-Up through Stabilizing to Stable operation. Eversolo specifies a warm-up time of within five minutes at an ambient temperature of 25°C.

    Internally, the C10 employs a toroidal transformer-based power supply. The power, clock, calibration, and output sections are physically separated and shielded to minimize electrical interference.

    The aluminum-alloy chassis measures 365 × 310 × 88mm, including its feet, and weighs 5.85kg.


    Completing the T10 and DAC-Z10 Digital Source System

    Eversolo positions the C10 as a companion to its T10 streaming transport and DAC-Z10.

    Both components support external 10MHz and 25MHz clock inputs, allowing the C10 to distribute a common reference signal through its independent BNC outputs.

    The potential benefits of external clocking, however, depend on the receiving equipment’s clock architecture and synchronization implementation. Improved reference-clock specifications do not automatically guarantee an audible improvement in every system.

    The C10 is a dedicated master clock rather than a streamer or DAC, and requires compatible external-clock-equipped components to serve its intended purpose.


    Pricing and Availability

    The Eversolo C10 is available for pre-order in the United States at $1,880. European pricing is listed at €1,890, while Australian pricing is A$2,999.

    A confirmed shipping date has not yet been announced.

    With the C10, Eversolo further expands its range of separate digital audio components, offering a dedicated timing reference alongside its streaming transports and DACs. Its combination of SC-cut OCXO technology, multiple buffered outputs, external reference synchronization, and real-time monitoring brings a distinctive approach to precision clocking in high-end audio systems.


    Source : Eversolo https://www.eversolo.com/en/products/c10