Eversolo C10 Brings Precision Clocking to Its Flagship Digital Audio System

Eversolo C10 master clock features a 10MHz SC-cut OCXO, four buffered BNC outputs, nine clock frequencies, GNSS 1PPS synchronization and an 8.8-inch touchscreen. US pre-order price is $1,880.


에버솔로 Eversolo C10

Eversolo C10

Eversolo has confirmed the full specifications and pricing of its C10 High-Precision Master Clock, a dedicated timing reference designed for high-performance digital audio systems. First shown at HIGH END Vienna 2026 in June, the C10 combines a custom 10MHz SC-cut OCXO with four independently buffered clock outputs, enabling compatible digital audio components to operate from a common timing reference.

The C10 completes Eversolo’s flagship digital source configuration alongside the T10 streaming transport and DAC-Z10 digital-to-analog converter.


SC-Cut OCXO for High-Stability Clock Generation

At the heart of the C10 is a custom 10MHz oven-controlled crystal oscillator (OCXO). By maintaining the crystal at a carefully regulated operating temperature, the oscillator minimizes frequency drift caused by changes in ambient conditions.

Eversolo employs an SC-cut (Stress Compensated Cut) quartz crystal, a design intended to reduce sensitivity to temperature variation and mechanical stress while improving long-term frequency stability and phase-noise performance.

The manufacturer specifies phase noise of no more than −115dBc/Hz at a 1Hz offset, −129dBc/Hz at 10Hz, −139dBc/Hz at 100Hz, and −145dBc/Hz at 1kHz. The quoted noise floor is −170dBc/Hz or lower.

Factory-calibrated frequency offset is specified at less than ±0.01ppm at 10MHz and 25°C, while short-term frequency stability is rated at better than 9×10⁻¹³ over a one-second measurement interval.


Four Independent Outputs and Nine Clock Frequencies

The C10 provides four BNC clock outputs, each equipped with a dedicated buffer circuit to minimize interactions between connected components.

Nine output frequencies are supported: 10MHz, 25MHz, 100MHz, 11.2896MHz, 22.5792MHz, 45.1584MHz, 12.288MHz, 24.576MHz, and 49.152MHz.

This range includes frequencies associated with both the 44.1kHz and 48kHz sampling-rate families, extending compatibility across different digital audio architectures.

The outputs deliver a 1.8Vrms square-wave signal with 50Ω output impedance. Compatibility depends on the connected component’s supported clock frequencies, signal requirements, and input configuration.


GNSS 1PPS Reference for Long-Term Accuracy

An SMB connector on the rear panel accepts an external GNSS-derived 1PPS (Pulse Per Second) reference signal.

By using this satellite-derived timing reference, the C10 can periodically correct its internal time base to maintain long-term frequency accuracy.

The arrangement combines the oscillator’s short-term stability with the long-term accuracy available from an external timing reference, providing an additional means of maintaining consistent clock performance during extended operation.


Real-Time Clock Monitoring on an 8.8-Inch Touchscreen

One of the C10’s most distinctive features is its 8.8-inch IPS touchscreen.

Rather than limiting feedback to a simple status indicator, the display presents the oscillator’s operating temperature, stabilization process, clock status, and 1PPS calibration information.

Users can follow the transition from Warm-Up through Stabilizing to Stable operation. Eversolo specifies a warm-up time of within five minutes at an ambient temperature of 25°C.

Internally, the C10 employs a toroidal transformer-based power supply. The power, clock, calibration, and output sections are physically separated and shielded to minimize electrical interference.

The aluminum-alloy chassis measures 365 × 310 × 88mm, including its feet, and weighs 5.85kg.


Completing the T10 and DAC-Z10 Digital Source System

Eversolo positions the C10 as a companion to its T10 streaming transport and DAC-Z10.

Both components support external 10MHz and 25MHz clock inputs, allowing the C10 to distribute a common reference signal through its independent BNC outputs.

The potential benefits of external clocking, however, depend on the receiving equipment’s clock architecture and synchronization implementation. Improved reference-clock specifications do not automatically guarantee an audible improvement in every system.

The C10 is a dedicated master clock rather than a streamer or DAC, and requires compatible external-clock-equipped components to serve its intended purpose.


Pricing and Availability

The Eversolo C10 is available for pre-order in the United States at $1,880. European pricing is listed at €1,890, while Australian pricing is A$2,999.

A confirmed shipping date has not yet been announced.

With the C10, Eversolo further expands its range of separate digital audio components, offering a dedicated timing reference alongside its streaming transports and DACs. Its combination of SC-cut OCXO technology, multiple buffered outputs, external reference synchronization, and real-time monitoring brings a distinctive approach to precision clocking in high-end audio systems.


Source : Eversolo https://www.eversolo.com/en/products/c10